If you are looking for a way to enjoy your herb or tobacco with a smooth and satisfying hit, you might want to try making your own glass bong. Glass bongs are not only aesthetically pleasing, but also durable, easy to clean, and customizable. You can make a glass bong from scratch using glass tubing and a propane torch, or you can use a recycled glass bottle and a drill bit. In this blog post, we will show you how to do both methods step by step.
How to Make a Glass Bong from Scratch
To make a glass bong from scratch, you will need the following materials:
- A piece of glass tubing (about 12 inches long and 1 inch in diameter)
- A glass bottle (preferably with a wide base and a long neck)
- A propane torch
- A working surface (such as a metal tray or a wooden board)
- A grommet or a cork (with a hole that fits the glass tubing)
- A stem or a tube (that fits into the grommet or the cork)
- A bowl (that fits onto the end of the stem or the tube)
Here are the steps to follow:
- Cut the glass tubing to the desired length. The length will depend on the size of the bong you want to create. You can use a glass cutter or a hacksaw to cut the tubing. Be careful not to cut yourself with the sharp edges.
- Heat the end of the glass tubing with the propane torch. Hold the tubing horizontally and rotate it slowly over the flame until it becomes soft and pliable. Be careful not to overheat or burn the glass.
- Bend the heated end of the tubing into a 90-degree angle. Use a pair of pliers or tongs to bend the tubing while it is still hot and soft. This will form the mouthpiece of your bong.
- Let the bent end of the tubing cool down completely. You can dip it in cold water or let it air dry.
- Clean the bottle and remove any labels or stickers. You can use warm water and soap to wash the bottle.
- Drill a hole in the bottle near the base. You can use a diamond drill bit or a regular drill bit with some lubricant (such as water or oil) to drill through the glass. The hole should be slightly smaller than the diameter of the grommet or the cork.
- Insert the grommet or the cork into the hole. You may need to use some glue or tape to secure it in place.
- Insert the stem or the tube into the grommet or the cork. The stem or the tube should be long enough to reach inside the bottle and submerge in water.
- Add the bowl to the end of the stem or the tube. You can use any bowl that fits snugly onto your stem or tube, such as a metal nut, a socket, or a glass bowl.
- Fill the bottle with water until it covers about an inch of the stem or tube.
- Test your bong by lighting some herb or tobacco in the bowl and inhaling from the mouthpiece. Adjust the water level if needed.
How to Make a Glass Bong from a Recycled Bottle
To make a glass bong from a recycled bottle, you will need the following materials:
- A glass bottle (preferably with a wide base and a long neck)
- A 3/4 inch diamond drill bit
- A battery powered drill
- A rubber grommet (with an outside diameter of 31/32 inch, an inner diameter of 1/2 inch, and a 3/4 inch groove)
- A 14mm glass downstem and bowl
Here are the steps to follow:
- Clean the bottle and remove any labels or stickers. You can use warm water and soap to wash the bottle.
- Mark a spot to drill on the upper curve of the body of the bottle. You can use a sharpie to trace a circle using the grommet as a guide.
- Prepare your tools by attaching the diamond drill bit to your drill. Be sure to use a battery powered drill, as you will be running water over the drilling area. You may also want to wear safety goggles to protect your eyes from glass shards.
- Get a steady stream of water over the drill spot. To keep the glass cool and prevent it from breaking, turn on the faucet and hold the bottle so the water runs over the spot you marked.
- Start drilling slowly. Set your drill to 3/4 of its max speed and gently push it against the marked spot. Do not apply too much pressure or force, as this may crack the glass. Let the drill bit do the work and be patient. It may take several minutes to drill through the glass.
- Stop drilling when you feel a sudden drop in resistance. This means you have drilled through the glass. Pull out the drill bit and rinse off any glass dust.
- Insert the grommet into the hole. You may need to use some lubricant (such as water or oil) to slide it in. Make sure it fits snugly and securely.
- Insert the downstem into the grommet. The downstem should be long enough to reach inside the bottle and submerge in water.
- Add the bowl to the end of the downstem. You can use any 14mm glass bowl that fits onto your downstem.
- Fill the bottle with water until it covers about an inch of the downstem.
- Test your bong by lighting some herb or tobacco in the bowl and inhaling from the mouthpiece. Adjust the water level if needed.
Conclusion
Making your own glass bong can be a fun and rewarding project. You can use either glass tubing and a propane torch, or a recycled glass bottle and a drill bit, to create a custom bong that suits your preferences. Glass bongs are easy to clean, durable, and smooth to smoke from. Just remember to be careful when working with glass and fire, and enjoy your homemade bong responsibly.
